CRittaler Posted May 11, 2022 Author Share Posted May 11, 2022 Glad you got the brake booster sorted. It is comforting when the hiss goes away. But did you notice any brake fluid in the old booster? If so it is likely that the master cylinder is leaking, and that can take out the booster. And the gauges look great. But I wouldn’t change the oil too soon. I’d drive the truck some and see if the pressure doesn’t come down after that. As for rotating pics, each phone has its own position for “normal” and if you find that and take the pics in that position you shouldn’t have to rotate them. The old booster was dry thankfully. I've got a ways to go still before the truck is road worthy so the oil can stay for now. Link to comment Share on other sites More sharing options...
CRittaler Posted May 11, 2022 Author Share Posted May 11, 2022 AFR at 14.5. Nice :) Thanks! I've done zero tuning on the AVS2, but at least I know the idle is good. Link to comment Share on other sites More sharing options...
Gary Lewis Posted May 11, 2022 Share Posted May 11, 2022 Thanks! I've done zero tuning on the AVS2, but at least I know the idle is good. The AVS2 is one of the easiest carbs to tune. Loosen the screw and swivel the plates out of the way and you can change the rods and springs, which lets you richen or lean the mix at cruise and determine when the enrichment happens for power. And if you really need to change jets just pull the cover w/o spilling a drop of gas. Link to comment Share on other sites More sharing options...
CRittaler Posted May 12, 2022 Author Share Posted May 12, 2022 Thanks! I've done zero tuning on the AVS2, but at least I know the idle is good. No pictures this time but I fished the trailer brake wire and my backup camera wires down the frame rail. Thankfully there is enough wire for the backup camera and I don't have to extend the harness. While I was under there I discovered more balls of electrical tape.... and more dang scotchloks this time on the tail light harness. I know the truck had a 7 pin trailer connector at some point because I removed the hacked up wiring when I bought it. I think these are a remnant of that. It looks like they're connected to the signals and reverse light wires. The "spare" bumper that came with the truck has a smashed up 7 pin connected which leads me to believe it's the original bumper and PO swapped it for some reason. For the 4 pin harness there is a plug adaptor that sits between 2 factory connectors and breaks out the necessary signals for the 4 pin harness. The trailer plug that I bought is a 4 pin/7pin combo that uses a standard 4 pin to connect its 4 pin connector so at least I don't have to solder that part. I'll only need to connect up the power/brake signal/aux backup/ground. Not too bad. EDIT: Also, just realized that I didn't provision for running that aux backup signal :( I'll leave it off for now I guess. Now I have to fix that wiring :/ Link to comment Share on other sites More sharing options...
kramttocs Posted May 12, 2022 Share Posted May 12, 2022 No pictures this time but I fished the trailer brake wire and my backup camera wires down the frame rail. Thankfully there is enough wire for the backup camera and I don't have to extend the harness. While I was under there I discovered more balls of electrical tape.... and more dang scotchloks this time on the tail light harness. I know the truck had a 7 pin trailer connector at some point because I removed the hacked up wiring when I bought it. I think these are a remnant of that. It looks like they're connected to the signals and reverse light wires. The "spare" bumper that came with the truck has a smashed up 7 pin connected which leads me to believe it's the original bumper and PO swapped it for some reason. For the 4 pin harness there is a plug adaptor that sits between 2 factory connectors and breaks out the necessary signals for the 4 pin harness. The trailer plug that I bought is a 4 pin/7pin combo that uses a standard 4 pin to connect its 4 pin connector so at least I don't have to solder that part. I'll only need to connect up the power/brake signal/aux backup/ground. Not too bad. EDIT: Also, just realized that I didn't provision for running that aux backup signal :( I'll leave it off for now I guess. Now I have to fix that wiring :/ May not be what you are wanting but after years of troubleshooting trailer lights not working in out flatbed farm trucks, I've started installing those junction boxes they use on trailer tongues in the frame behind the last cross member. That way it's easier to troubleshoot as well as replace the trailer connector if needed. Just mentioning it if the scotchloks have split the factory wiring and if it would make sense to remove the T adapter and terminate the factory wiring (after the factory connector) into the junction box. Link to comment Share on other sites More sharing options...
CRittaler Posted May 12, 2022 Author Share Posted May 12, 2022 May not be what you are wanting but after years of troubleshooting trailer lights not working in out flatbed farm trucks, I've started installing those junction boxes they use on trailer tongues in the frame behind the last cross member. That way it's easier to troubleshoot as well as replace the trailer connector if needed. Just mentioning it if the scotchloks have split the factory wiring and if it would make sense to remove the T adapter and terminate the factory wiring (after the factory connector) into the junction box. That's a good idea! I'll look at ordering a waterproof junction box. Link to comment Share on other sites More sharing options...
FuzzFace2 Posted May 12, 2022 Share Posted May 12, 2022 May not be what you are wanting but after years of troubleshooting trailer lights not working in out flatbed farm trucks, I've started installing those junction boxes they use on trailer tongues in the frame behind the last cross member. That way it's easier to troubleshoot as well as replace the trailer connector if needed. Just mentioning it if the scotchloks have split the factory wiring and if it would make sense to remove the T adapter and terminate the factory wiring (after the factory connector) into the junction box. That's a good idea! I'll look at ordering a waterproof junction box. On the back up light wire I would not worry about it. In all the trailers dad & I have pulled only 1 (travel trailer) had back up lights and they were not connected to the puller. If you wanted them on there was a switch in the storage box out back they were mounted to. Yes they were useless for seeing when backing up as they were not vary bright. My pickup is the first to use a after market Tee that plugs in between the rail harness & tail light harness and I cant remember if it has the back up wire in it now? I did have to run the trailer brake & power wire (10 ga for both) from up front to the 7 pin out back. If I need to run a flat 4 plug I have adapter behind the seat that will plug into the 7 pin and make it flat 4. My 02 Dodge came from the factory with the adapter and in the 20 years I have had the truck I have never needed to use it. One day I should hook the pick up to my car trailer to make sure the wiring is right before I need to use it LOL Dave ---- Link to comment Share on other sites More sharing options...
CRittaler Posted May 12, 2022 Author Share Posted May 12, 2022 On the back up light wire I would not worry about it. In all the trailers dad & I have pulled only 1 (travel trailer) had back up lights and they were not connected to the puller. If you wanted them on there was a switch in the storage box out back they were mounted to. Yes they were useless for seeing when backing up as they were not vary bright. My pickup is the first to use a after market Tee that plugs in between the rail harness & tail light harness and I cant remember if it has the back up wire in it now? I did have to run the trailer brake & power wire (10 ga for both) from up front to the 7 pin out back. If I need to run a flat 4 plug I have adapter behind the seat that will plug into the 7 pin and make it flat 4. My 02 Dodge came from the factory with the adapter and in the 20 years I have had the truck I have never needed to use it. One day I should hook the pick up to my car trailer to make sure the wiring is right before I need to use it LOL Dave ---- This is what I bought: https://www.reesetowpower.com/product/85343_trailer-connector-adapter-7-to-4-flat I plan on heat shrinking over the reverse light connection for the time being. I think the 4 pin is Left turn/stop, right turn/stop, tail/marker, and ground. I've got the same trailer brake (12ga) and power (10ga) running along the frame rail. Link to comment Share on other sites More sharing options...
FuzzFace2 Posted May 12, 2022 Share Posted May 12, 2022 This is what I bought: https://www.reesetowpower.com/product/85343_trailer-connector-adapter-7-to-4-flat I plan on heat shrinking over the reverse light connection for the time being. I think the 4 pin is Left turn/stop, right turn/stop, tail/marker, and ground. I've got the same trailer brake (12ga) and power (10ga) running along the frame rail. So that setup you have to have a flat 4 wired in to the truck for most of the wiring from the looks of it. My Tee came on 1 of my trucks and fits between the frame rail harness and the tail light harness. You unplug the 2 and plug the Tee into the rail harness and then the tail light harness into the Tee. https://www.etrailer.com/Custom-Fit-Vehicle-Wiring/Ford/F-100,+F-150,+F-250,+F-350/1981/118313.html?VehicleID=19811171986 I cut the flat 4 off and wired it into the 7 pin along with the brake & power wires. Both the brake & power are 10 ga wire as I did not want to have a power drop on either system before it got to the trailer. A few days after I ran the wires for brake & power I did not see my fuel gauge move? Having duel tanks I flipped the switch and see the other tank (rear) that should be full at half tank? When I ran the 2 wires to the rear the wire for the tank switch valve hit the frame at a bad splice I made and blew the fuse and by default goes to the rear tank. I fixed the splice, replaced the fuse and been all good since. So if something is not working after pulling the wires look over the frame rail harness really good. Dave ---- Link to comment Share on other sites More sharing options...
CRittaler Posted May 12, 2022 Author Share Posted May 12, 2022 This is what I bought: https://www.reesetowpower.com/product/85343_trailer-connector-adapter-7-to-4-flat I plan on heat shrinking over the reverse light connection for the time being. I think the 4 pin is Left turn/stop, right turn/stop, tail/marker, and ground. I've got the same trailer brake (12ga) and power (10ga) running along the frame rail. So that setup you have to have a flat 4 wired in to the truck for most of the wiring from the looks of it. My Tee came on 1 of my trucks and fits between the frame rail harness and the tail light harness. You unplug the 2 and plug the Tee into the rail harness and then the tail light harness into the Tee. https://www.etrailer.com/Custom-Fit-Vehicle-Wiring/Ford/F-100,+F-150,+F-250,+F-350/1981/118313.html?VehicleID=19811171986 I cut the flat 4 off and wired it into the 7 pin along with the brake & power wires. Both the brake & power are 10 ga wire as I did not want to have a power drop on either system before it got to the trailer. A few days after I ran the wires for brake & power I did not see my fuel gauge move? Having duel tanks I flipped the switch and see the other tank (rear) that should be full at half tank? When I ran the 2 wires to the rear the wire for the tank switch valve hit the frame at a bad splice I made and blew the fuse and by default goes to the rear tank. I fixed the splice, replaced the fuse and been all good since. So if something is not working after pulling the wires look over the frame rail harness really good. Dave ---- My truck has the same T connector to break out a 4 pin. The PO added additional wires (poorly) to wire in a separate 7 pin connector that is no longer present. I'm undoing his terrible wiring and redoing it with the Resse connector I bought. It will be: aftermarket T to 4 flat --> plug into the Resse harness to give me a panel mount 4 flat. This way I only need to wire in the heavy gauge wires to the 7 pin. I have to repair the factory harness where the PO used the scotchloks to spice for their non existent 7 pin. Link to comment Share on other sites More sharing options...
Recommended Posts