Axle seal replacement Dana44HD?

Where do I get these?

https://photos.app.goo.gl/agMFovhUCDqstkza7

https://photos.app.goo.gl/71CS5PegUsH7vqxeA

https://photos.app.goo.gl/YkyXbRKNDgXAShTN9

https://photos.app.goo.gl/broZ1YMZTpVMBjEY7

3C132 'grease retainer'?
That Chicago Rawhide 531904 is so obsolete it's hard to find a cross.

Looks like Torque King sells it as a kit w/ that inner spindle roller bearing you were asking about before.

https://torqueking.com/product/40534/qu40534-right-side-diff-output-bearing-and-seal-kit-for-ford-dana-ifs/

JBG sells the same set for 1/2 the price.

https://shop.broncograveyard.com/D44-OE-Spicer-TTB-Housing-Axle-Bearing-Kit-Right-Side/productinfo/32014/

Nine years ago Gary said this: https://www.ford-trucks.com/forums/1305477-dana-44-ttb-axle-shaft-seal-part-help.html

While I'm sitting here on a slow night I managed to turn up this.  https://downtofab.com/products/spicer-50492

Perhaps it what you need?
I can't cross the Spicer # but if you can read the BOM on your axle you can check it on their website.
Or you could pull out a digital caliper and measure what you have.

Thanks Jim,

I found that one too on their website, and that's also th one they showed me , in-stock, at the local NAPA. They did some research too, and were telling me the same "...difficult to find them anymore". I'll keep searching. I'm headed to the Ford dealership today. I have not seen an alternative configuration or stackup of parts that I can make-do with. I have nearly all of the different options in my shop right now but have not figured it out yet.

Thanks for you effort on your "..slow night"

D3TZ-3C132-A is discontinued by Ford but they were available a decade ago, as seen here: https://www.ford-trucks.com/forums/1145110-calling-all-ctubutiss-and-numberdummys.html

I've found two different listings on eBay.
They're both about $15 with shipping.

Rear counter says Green Sales has 135 and NOS Parts has 16

https://www.rearcounter.com/D3TZ-3C132-A-parts190958.html

Jim,


thanks again, your direction to Gary's post, lead me to confirming that this was the SKF-BK1 kit I needed, although I've already installed the needle (thrust bearing) bearing and seal the remainder of the seal /slinger was broken down into components and looks to be the right fit. I'll post back once I pick up the parts from my local NAPA.

Last piece before re-assembly of the front end... Stay-tuned....

 New here and used the information to buy the same kit for the same seal!  

They did not have just the seal listed as Driveworks Oil Seal Part # S-722109 Front Inner; Brand may vary by location., Spicer 44 Axle; 2 Req.

2Cast wrote

New here and used the information to buy the same kit for the same seal!  

They did not have just the seal listed as Driveworks Oil Seal Part # S-722109 Front Inner; Brand may vary by location., Spicer 44 Axle; 2 Req.

Welcome!  Glad you joined.  

However, you may have missed the email you were sent asking you to go to the New Members Start Here folder, read the guidelines, and then post an intro there.  We do that because we hold everyone to the guidelines and want to ensure you've seen them.

Don't worry, this happens a lot.  But please go do that before we go further.