Diary of a Restore (Thread)

[AmericanSavage]

Foam Arrived. I got it all on. Pic below.

Had to take wheels off to install the trim better.

And I may have discovered another issue: The D side front wheel, when I had the truck slightly jacked off the ground, I noticed the Front D-side Tie Rod end, when the wheel is moved--the bolt from the tie rod end in the Knuckle, moves back and forth like it is loose! I can see the king nut move back and forth like it is loose in the spindle, if that makes sense.

So, I am hope this is just a wore out tie rod end, and NOT the tapered hole in the spindle that the bolt on the tie rod end goes through. I assume the knuckle is a tougher cast iron than that bolt.

Shopping for tie rod ends now. Man, it is difficult to find 4x4 ends--MOOG (my choice usually) makes not one for D-side 4x4 and my year/fitment.

Onward. Anyone ever dealt with such an issue on Tie Rod and Knuckle?

 

[mat in tn]

Foam Arrived. I got it all on. Pic below.

Had to take wheels off to install the trim better.

And I may have discovered another issue: The D side front wheel, when I had the truck slightly jacked off the ground, I noticed the Front D-side Tie Rod end, when the wheel is moved--the bolt from the tie rod end in the Knuckle, moves back and forth like it is loose! I can see the king nut move back and forth like it is loose in the spindle, if that makes sense.

So, I am hope this is just a wore out tie rod end, and NOT the tapered hole in the spindle that the bolt on the tie rod end goes through. I assume the knuckle is a tougher cast iron than that bolt.

Shopping for tie rod ends now. Man, it is difficult to find 4x4 ends--MOOG (my choice usually) makes not one for D-side 4x4 and my year/fitment.

Onward. Anyone ever dealt with such an issue on Tie Rod and Knuckle?

I'm a little bugged by the description. is the castle nut tight and held by a cotter pin? if all is tight then I would pull it and inspect both male and female for wear or galling. it is a tapered connection so to wedge in place. the only wear point should be the ball joint itself. I have found them loose before most likely by having been installed with the vehicle sitting on the wheels and the wrench turner did not realize they were tightening against the geometry rather than pulling the wedge into place and basically not tightening it fully.

[AmericanSavage]

I'm a little bugged by the description. is the castle nut tight and held by a cotter pin? if all is tight then I would pull it and inspect both male and female for wear or galling. it is a tapered connection so to wedge in place. the only wear point should be the ball joint itself. I have found them loose before most likely by having been installed with the vehicle sitting on the wheels and the wrench turner did not realize they were tightening against the geometry rather than pulling the wedge into place and basically not tightening it fully.

Sorry about the description. It was hard to describe. The king nut--with the pin--was seated all the way down. The tie rod was still loose.

The nut was rusted on. When I tried to get it off, the tie rod internals spun with EASE. Nut splitter? Nada. I had to wheel it apart carefully. It screwed off, and the end simply fell off.

Pics below.

I wonder if the correct tie rod end was even in it it was so loose and yet, it appears, the nut was bottomed out.

New ends come this week. Will check fit before anything.

As another thing I have to fix, the u joint on D-side tire in ONE spot is loose and can easily be moved--bearing is shot there too. So, I will be schooling myself on how to replace that as well.

Last Park brake cable comes tomorrow! Amazon is taking a LONG time to deliver lately.

[mat in tn]

I'm a little bugged by the description. is the castle nut tight and held by a cotter pin? if all is tight then I would pull it and inspect both male and female for wear or galling. it is a tapered connection so to wedge in place. the only wear point should be the ball joint itself. I have found them loose before most likely by having been installed with the vehicle sitting on the wheels and the wrench turner did not realize they were tightening against the geometry rather than pulling the wedge into place and basically not tightening it fully.

Sorry about the description. It was hard to describe. The king nut--with the pin--was seated all the way down. The tie rod was still loose.

The nut was rusted on. When I tried to get it off, the tie rod internals spun with EASE. Nut splitter? Nada. I had to wheel it apart carefully. It screwed off, and the end simply fell off.

Pics below.

I wonder if the correct tie rod end was even in it it was so loose and yet, it appears, the nut was bottomed out.

New ends come this week. Will check fit before anything.

As another thing I have to fix, the u joint on D-side tire in ONE spot is loose and can easily be moved--bearing is shot there too. So, I will be schooling myself on how to replace that as well.

Last Park brake cable comes tomorrow! Amazon is taking a LONG time to deliver lately.

please do compare the new end to the one removed; it may even help another with something to watch for. it does look as though the two were not fully seated. as for the u joint, is there any gear oil leaking out? it looks dry in the picture.

[AmericanSavage]

please do compare the new end to the one removed; it may even help another with something to watch for. it does look as though the two were not fully seated. as for the u joint, is there any gear oil leaking out? it looks dry in the picture.

Will do on all counts. The new tie rod ends are on the way.

No gear oil at the u joint at all. HOWEVER, in the front differential, where the axles go in, there is some seepage. I am betting those seals are also shot.

[AmericanSavage]

please do compare the new end to the one removed; it may even help another with something to watch for. it does look as though the two were not fully seated. as for the u joint, is there any gear oil leaking out? it looks dry in the picture.

Will do on all counts. The new tie rod ends are on the way.

No gear oil at the u joint at all. HOWEVER, in the front differential, where the axles go in, there is some seepage. I am betting those seals are also shot.

OK, as Mat Requested:

I calipered the new Left Outer tie rod end, with the old. There is MAYBE a thousands of the inch difference—the new one being that much wider.

The right is far thinner, by tenths.

I only put the left on for now. COLD! But, it was a bear—I had to cut the adj sleeve off as it was rusted on—heat, blaster, nada.

The new sleeve was a bear to screw on. I mean really tough. The left outer tie rod is left hand thread too…took me a while to figure that out.

Now to the pertinent issue—the new and the old outer tie rod bottomed out with the king nut and spun—not fully seated. I am not sure this is wise, but the only way to get the nut on and torque to 50 ft. lbs., was to use 1 grade 8 washer. Then the nut pulled up the joint fully to seat and the ball joint did not spin.

Is this an aftermarket issue? The one that came out and the one that went in are all similar in every way that matters. Pic follows.

Rear parking brake cable is next, and I am having a lot of trouble figuring out the front D side axle shaft process. Will post in separate thread.

 

[Gary Lewis]

OK, as Mat Requested:

I calipered the new Left Outer tie rod end, with the old. There is MAYBE a thousands of the inch difference—the new one being that much wider.

The right is far thinner, by tenths.

I only put the left on for now. COLD! But, it was a bear—I had to cut the adj sleeve off as it was rusted on—heat, blaster, nada.

The new sleeve was a bear to screw on. I mean really tough. The left outer tie rod is left hand thread too…took me a while to figure that out.

Now to the pertinent issue—the new and the old outer tie rod bottomed out with the king nut and spun—not fully seated. I am not sure this is wise, but the only way to get the nut on and torque to 50 ft. lbs., was to use 1 grade 8 washer. Then the nut pulled up the joint fully to seat and the ball joint did not spin.

Is this an aftermarket issue? The one that came out and the one that went in are all similar in every way that matters. Pic follows.

Rear parking brake cable is next, and I am having a lot of trouble figuring out the front D side axle shaft process. Will post in separate thread.

I've not had a problem getting them to seat, but I see no reason that a G8 washer would hurt anything. It is harder than the casting so won't flex.

[AmericanSavage]

I've not had a problem getting them to seat, but I see no reason that a G8 washer would hurt anything. It is harder than the casting so won't flex.

Thanks Gary. It looks like both old and new simply ran out of threads. I will pic the washer, etc. in a later post

Stay warm this weekend. We are freezing in NC.

[Gary Lewis]

I've not had a problem getting them to seat, but I see no reason that a G8 washer would hurt anything. It is harder than the casting so won't flex.

Thanks Gary. It looks like both old and new simply ran out of threads. I will pic the washer, etc. in a later post

Stay warm this weekend. We are freezing in NC.

It is currently 58F here, by far the warmest it has been for what seems like a month but is probably just a week.

[mat in tn]

It is currently 58F here, by far the warmest it has been for what seems like a month but is probably just a week.

it's definitely cold here in NC. but after reading about the wind chill recorded on mt Washington yesterday I refuse to complain. its above freezing. and all the signs of spring are looming. my wife cut fresh buttercups yesterday and brought them in. can't complain about that.

as to the washer I think you are fine with it. sure, it is not supposed to be needed. in theory it's possible that the machining / casting differences are what caused this. or possibly it is from hard livin. loose taper joints wear. loose taper joints also hold moisture and rust. rusty joints wear more. and so on. if in its life it was not torqued to spec and was not seated properly this might be the result. theory for certain but if you got it torqued to spec with a washer, roll with it. in doing the safety check on an f 250 I found the drag link tightened with the castle nut and cotter pin in place yet as soon as i lifted one wheel to check for joint play it flopped like it was shot. I tightened it three more rounds to spec. there is no telling how long that truck was wandering all over the road with the driver saying "it can't be that. its new"!