Grease Gun

[BigBrother-84]

There are effective degreasers that can break down and remove grease from different surfaces, making cleaning easier before using a new grease gun.

You're right Chantal, working with a clean gun (and any tool, in fact) is much more pleasant.

But I have to admit that, even clean, this tool I my most detestable one.

Since I use it 3-4 times a year on my little Kubota tractor, I don't clean it too often and tolerate it dirty as it is.

By the way, what's a good frequency for greasing a Bullnose?

[ArdWrknTrk]

There are effective degreasers that can break down and remove grease from different surfaces, making cleaning easier before using a new grease gun.

You're right Chantal, working with a clean gun (and any tool, in fact) is much more pleasant.

But I have to admit that, even clean, this tool I my most detestable one.

Since I use it 3-4 times a year on my little Kubota tractor, I don't clean it too often and tolerate it dirty as it is.

By the way, what's a good frequency for greasing a Bullnose?

Since I change my own oil I try to give the drive line and front steering/suspension a shot of grease while the pan is draining.

I generally run semi synthetic diesel oil and OCI of 5k.(miles)

Though I am about ready to swap out the Motul 8100 that Amazon recommended as a deal.

ETA: It's a "while I'm there" kind of thing, and probably every 6 months is closer to the factory service

[Gary Lewis]

There are effective degreasers that can break down and remove grease from different surfaces, making cleaning easier before using a new grease gun.

You're right Chantal, working with a clean gun (and any tool, in fact) is much more pleasant.

But I have to admit that, even clean, this tool I my most detestable one.

Since I use it 3-4 times a year on my little Kubota tractor, I don't clean it too often and tolerate it dirty as it is.

By the way, what's a good frequency for greasing a Bullnose?

Jeff - I think the frequency depends on many things. Obviously one would be mileage, and the 85 owners manual says do that every 7,500 miles for steering linkage and driveline. But another thing is driving conditions, as the manual also says to do lube every 1,000 miles if you drive in water or mud.

Another would be the type of grease you use. What I've been using previously had been separating in the vehicle and dripping a bit after usage. But the stuff I got with the Lube Shuttle doesn't do that, so I think it'll be good for longer.

[ArdWrknTrk]

Another would be the type of grease you use. What I've been using previously had been separating in the vehicle and dripping a bit after usage. But the stuff I got with the Lube Shuttle doesn't do that, so I think it'll be good for longer.

In the vehicle??? or in the gun?

Definitely be conscious of what grease you use where. Like you never want to use EP moly grease in something like a driveshaft where it will pack up into flakes and leave the joint starved for lubrication.

 

[Gary Lewis]

Another would be the type of grease you use. What I've been using previously had been separating in the vehicle and dripping a bit after usage. But the stuff I got with the Lube Shuttle doesn't do that, so I think it'll be good for longer.

In the vehicle??? or in the gun?

Both. Made a huge mess on the shelf and a bit of a mess under the truck. That grease, whatever it was, was the worst. But all the greases I've used have separated over time in the gun. The stuff from Lube Shuttle hasn't, so far. And it has been almost a year.

[BigBrother-84]

Both. Made a huge mess on the shelf and a bit of a mess under the truck.

Before living for Big Brother's Big Tour, I generously lubed the direction and driveshaft.

As result, the driveshaft spread a nice ring of grease under the truck body, exhaust pipe, and on floor, at the first start.

Maybe I was too enthusiastic with the grease gun.