ArdWrknTrk Posted March 29, 2022 Share Posted March 29, 2022 That’s ok, I’ll take some regular wrenches to it and get the size. ACE hardware is super close. Here is a pic of the box and the AFR box lurking in the background: Pretty! 🤩 Listing shows a 5/16 male inverted flare which is 1/2-20 thread line nut. I would guess 5/8 wrench.... Link to comment Share on other sites More sharing options...
Gsmblue Posted March 29, 2022 Author Share Posted March 29, 2022 Pretty! 🤩 Listing shows a 5/16 male inverted flare which is 1/2-20 thread line nut. I would guess 5/8 wrench.... Thank you on both counts! Link to comment Share on other sites More sharing options...
Gary Lewis Posted March 29, 2022 Share Posted March 29, 2022 That’s ok, I’ll take some regular wrenches to it and get the size. ACE hardware is super close. Here is a pic of the box and the AFR box lurking in the background: Yes, that IS pretty! Good luck with it. Link to comment Share on other sites More sharing options...
Gsmblue Posted March 29, 2022 Author Share Posted March 29, 2022 Yes, that IS pretty! Good luck with it. Ok, I have found crows feet wrenches. I could not find line ones, but I do have a set of flare wrenches, so I can crack them with that then use crows feet, I see minimal risk of damaging anything. ATF-F aquired. Should start tackling later today :) Link to comment Share on other sites More sharing options...
ArdWrknTrk Posted March 29, 2022 Share Posted March 29, 2022 Ok, I have found crows feet wrenches. I could not find line ones, but I do have a set of flare wrenches, so I can crack them with that then use crows feet, I see minimal risk of damaging anything. ATF-F aquired. Should start tackling later today :) You can get it with a regular crowfoot. The line wrench helps keep it from slipping off. There's really no room to swing a wrench, even with deep offset. Link to comment Share on other sites More sharing options...
Gsmblue Posted March 29, 2022 Author Share Posted March 29, 2022 You can get it with a regular crowfoot. The line wrench helps keep it from slipping off. There's really no room to swing a wrench, even with deep offset. Cheers Jim. I look forward to starting this. In other news - I am taking the Bronco back to the transmission shop 10 am tomorrow.. Link to comment Share on other sites More sharing options...
Gary Lewis Posted March 29, 2022 Share Posted March 29, 2022 Cheers Jim. I look forward to starting this. In other news - I am taking the Bronco back to the transmission shop 10 am tomorrow.. Good luck on both issues! Link to comment Share on other sites More sharing options...
ArdWrknTrk Posted March 29, 2022 Share Posted March 29, 2022 Cheers Jim. I look forward to starting this. In other news - I am taking the Bronco back to the transmission shop 10 am tomorrow.. I wish you luck, and satisfaction. 👍 But I spoke my piece way back when you first had problems... Link to comment Share on other sites More sharing options...
Gsmblue Posted March 29, 2022 Author Share Posted March 29, 2022 I wish you luck, and satisfaction. 👍 But I spoke my piece way back when you first had problems... Thanks Gents. I am over this transmission BS I am meeting the owner tomorrow. My plan is to be a pest to them through to the end of the warranty in August. Then order a built transmission and do the swap myself. I will then take this POS to their shop and push it off the back of my truck in the middle of their parking lot. Link to comment Share on other sites More sharing options...
ArdWrknTrk Posted March 29, 2022 Share Posted March 29, 2022 Thanks Gents. I am over this transmission BS I am meeting the owner tomorrow. My plan is to be a pest to them through to the end of the warranty in August. Then order a built transmission and do the swap myself. I will then take this POS to their shop and push it off the back of my truck in the middle of their parking lot. .... This doesn't bode well for Mrs Blue this summer. ☹️ Link to comment Share on other sites More sharing options...
Recommended Posts