ClayJ Posted June 9, 2020 Author Share Posted June 9, 2020 And you still don't need a 12,000 RPM flexplate in a 5,000 RPM farm truck... But hey, it's your money! 😉 Umm not looking to reach 12k rpms. You're right it is my money and I'm having to spend it to correct a bad engine that has broken/cracked 4 flexplates. So forgive me if I'm looking for recommendations other than the standard steel welded plate. Maybe I'm just not picking up on your humor. Link to comment Share on other sites More sharing options...
Gary Lewis Posted June 9, 2020 Share Posted June 9, 2020 Umm not looking to reach 12k rpms. You're right it is my money and I'm having to spend it to correct a bad engine that has broken/cracked 4 flexplates. So forgive me if I'm looking for recommendations other than the standard steel welded plate. Maybe I'm just not picking up on your humor. I'm not up to speed on flexplates as I've not purchased one. Just used the Motorcraft ones that came on vehicles. But, looking at Rock Auto I only see two brands for the 351M: ATP & Pioneer. You've broken a Pioneer and the ATP is even less expensive. But, that gave me a part number, D1AZ6375A the same as you have, and a search for that found this post by Bill/Numberdummy back on FTE. At that time, 11 years ago, Bill found 32 of them in various Ford dealers. But, the MSRP was $186.57, which may tell us something about the quality of the ones at about $30. So, if it was me, I'd call the dealerships that had the flexplates way back then and see if they still do and at what price? Bill supplied the phone numbers. And, if that doesn't pan out I'd look for something stronger than the $30 ones - even if it means going billet. In your shoes I'd be DONE with breaking them and wanting something that absolutely will not break. In fact, in light of the Motorcraft unit being so expensive, I'd seriously consider using that money for a STRONG aftermarket one. Link to comment Share on other sites More sharing options...
ArdWrknTrk Posted June 9, 2020 Share Posted June 9, 2020 Umm not looking to reach 12k rpms. You're right it is my money and I'm having to spend it to correct a bad engine that has broken/cracked 4 flexplates. So forgive me if I'm looking for recommendations other than the standard steel welded plate. Maybe I'm just not picking up on your humor. You're right, I should use the laughing smiley so I don't come off as an ass. What I'm saying is the fault lies somewhere else. Millions and millions of vehicles get by with stock or replacement flex plates. Fix the underlying cause and the symptom goes away. Again, it's your money and if throwing a new engine at it is a better solution that using a dial test indicator on the crank flange to see if it's bent or end float is unreasonable, that's up to you. Link to comment Share on other sites More sharing options...
1986F150Six Posted June 9, 2020 Share Posted June 9, 2020 But, looking at Rock Auto I only see two brands for the 351M: ATP & Pioneer. You've broken a Pioneer and the ATP is even less expensive. But, that gave me a part number, D1AZ6375A the same as you have, and a search for that found this post by Bill/Numberdummy back on FTE. At that time, 11 years ago, Bill found 32 of them in various Ford dealers. But, the MSRP was $186.57, which may tell us something about the quality of the ones at about $30. So, if it was me, I'd call the dealerships that had the flexplates way back then and see if they still do and at what price? Bill supplied the phone numbers. And, if that doesn't pan out I'd look for something stronger than the $30 ones - even if it means going billet. In your shoes I'd be DONE with breaking them and wanting something that absolutely will not break. https://www.ebay.com/itm/NOS-1971-1978-FORD-351M-400-C6-AUTO-TRANS-FLYWHEEL-FLEX-PLATE-D1AZ-6375-A-NEW-/371420869716 In fact, in light of the Motorcraft unit being so expensive, I'd seriously consider using that money for a STRONG aftermarket one. https://www.ebay.com/itm/Ford-flexplate-70s-80s-engine-D1AZ-6375A-never-used-325/264753001876?hash=item3da4823594:g:598AAOSwGTBe2F8c Link to comment Share on other sites More sharing options...
Gary Lewis Posted June 9, 2020 Share Posted June 9, 2020 But, looking at Rock Auto I only see two brands for the 351M: ATP & Pioneer. You've broken a Pioneer and the ATP is even less expensive. But, that gave me a part number, D1AZ6375A the same as you have, and a search for that found this post by Bill/Numberdummy back on FTE. At that time, 11 years ago, Bill found 32 of them in various Ford dealers. But, the MSRP was $186.57, which may tell us something about the quality of the ones at about $30. So, if it was me, I'd call the dealerships that had the flexplates way back then and see if they still do and at what price? Bill supplied the phone numbers. And, if that doesn't pan out I'd look for something stronger than the $30 ones - even if it means going billet. In your shoes I'd be DONE with breaking them and wanting something that absolutely will not break. https://www.ebay.com/itm/NOS-1971-1978-FORD-351M-400-C6-AUTO-TRANS-FLYWHEEL-FLEX-PLATE-D1AZ-6375-A-NEW-/371420869716 In fact, in light of the Motorcraft unit being so expensive, I'd seriously consider using that money for a STRONG aftermarket one. https://www.ebay.com/itm/Ford-flexplate-70s-80s-engine-D1AZ-6375A-never-used-325/264753001876?hash=item3da4823594:g:598AAOSwGTBe2F8c MY GOODNESS! That is NOT GOLD! Link to comment Share on other sites More sharing options...
ArdWrknTrk Posted June 9, 2020 Share Posted June 9, 2020 MY GOODNESS! That is NOT GOLD! But lots of people think NOS is. I could understand IF you are looking for a concours vehicle. But, I'd pay my money and roll my dice. Link to comment Share on other sites More sharing options...
ClayJ Posted June 12, 2020 Author Share Posted June 12, 2020 Truck IS good and strong, but if Clay is going to toss it for reman, he more than likely's going to trade it for core. Truck IS NOT good and strong. Rusty's engine is out for inspection and tear down. Crankshaft runout is excessive and the main bearing caps don't look good at all. Pretty disappointed for being a, "rebuild" with less than 10k miles. Engine mounts are cracked, 1 spark plug was completely fouled and another was cracked. So I'll probably tear this engine down after the shop gets the new 400 installed. The cylinder heads are probably good so I'll sell those and whatever other components that aren't completely "wallered out." I did decide to go with a TCI heavy duty forged flexplate with a SFI 29.1 rating, so it should outlast the truck which is good because I'm D O N E replacing $40 hecho en mexico flexplates. Seems I was mistaken in a previous post as the transmission shop had checked end play and not run-out. So there it is ladies and gentleman, the smoking gun. Link to comment Share on other sites More sharing options...
ArdWrknTrk Posted June 12, 2020 Share Posted June 12, 2020 Truck IS good and strong, but if Clay is going to toss it for reman, he more than likely's going to trade it for core. Truck IS NOT good and strong. Rusty's engine is out for inspection and tear down. Crankshaft runout is excessive and the main bearing caps don't look good at all. Pretty disappointed for being a, "rebuild" with less than 10k miles. Engine mounts are cracked, 1 spark plug was completely fouled and another was cracked. So I'll probably tear this engine down after the shop gets the new 400 installed. The cylinder heads are probably good so I'll sell those and whatever other components that aren't completely "wallered out." I did decide to go with a TCI heavy duty forged flexplate with a SFI 29.1 rating, so it should outlast the truck which is good because I'm D O N E replacing $40 hecho en mexico flexplates. Seems I was mistaken in a previous post as the transmission shop had checked end play and not run-out. So there it is ladies and gentleman, the smoking gun. Well I'm glad you got to the bottom of this! Like I said in the beginning, I'd put a DTI on the crank flange and make sure the crank was straight. I hope your new combo out-performs and outlasts your expectations! ETA: I can only really go by how Gary raved about Rusty's engine back in the day. I never drove him, but trusted Gary's honest assessment at the time. Link to comment Share on other sites More sharing options...
Gary Lewis Posted June 13, 2020 Share Posted June 13, 2020 Truck IS good and strong, but if Clay is going to toss it for reman, he more than likely's going to trade it for core. Truck IS NOT good and strong. Rusty's engine is out for inspection and tear down. Crankshaft runout is excessive and the main bearing caps don't look good at all. Pretty disappointed for being a, "rebuild" with less than 10k miles. Engine mounts are cracked, 1 spark plug was completely fouled and another was cracked. So I'll probably tear this engine down after the shop gets the new 400 installed. The cylinder heads are probably good so I'll sell those and whatever other components that aren't completely "wallered out." I did decide to go with a TCI heavy duty forged flexplate with a SFI 29.1 rating, so it should outlast the truck which is good because I'm D O N E replacing $40 hecho en mexico flexplates. Seems I was mistaken in a previous post as the transmission shop had checked end play and not run-out. So there it is ladies and gentleman, the smoking gun. Well, in a twisted way I'm glad the crank had runout. At least you found something. I HATE it when I can't find the problem and then it goes away. I never know how long it is going to stay away and when it might raise its ugly head. And this does seem to explain why the flexplates broke. When it appeared the tranny shop had given the engine a clean bill of health it looked like there was no smoking gun. Like one of those mystery novels where the guy has been shot but there's no bullet, only to find out later the bullet was made of ice and it melted after killing him. I'm certainly sorry you are having these problems. Especially since I sold the truck to your FiL. Â Link to comment Share on other sites More sharing options...
Ray Cecil Posted June 13, 2020 Share Posted June 13, 2020 Well, in a twisted way I'm glad the crank had runout. At least you found something. I HATE it when I can't find the problem and then it goes away. I never know how long it is going to stay away and when it might raise its ugly head. And this does seem to explain why the flexplates broke. When it appeared the tranny shop had given the engine a clean bill of health it looked like there was no smoking gun. Like one of those mystery novels where the guy has been shot but there's no bullet, only to find out later the bullet was made of ice and it melted after killing him. I'm certainly sorry you are having these problems. Especially since I sold the truck to your FiL. Its an old truck Gary...you cant tell a buyer about something you didnt know. This happens sometimes. Not your fault. Link to comment Share on other sites More sharing options...
Recommended Posts