85lebaront2 Posted August 11, 2019 Share Posted August 11, 2019 Too bad Florida man didn't have that kind of luck when he was cutting into Big Blue. Aside from cops and the occasional overdose of bath salts or meth, nothing can stop Florida Man! I'm guessing some of the above was involved. It could have been Margaritaville. Link to comment Share on other sites More sharing options...
salans7 Posted August 12, 2019 Share Posted August 12, 2019 It could have been Margaritaville. Link to comment Share on other sites More sharing options...
Gary Lewis Posted August 12, 2019 Author Share Posted August 12, 2019 I like it: Link to comment Share on other sites More sharing options...
ArdWrknTrk Posted August 15, 2019 Share Posted August 15, 2019 Somehow I forgot to post pictures. The wobbly old output shaft I even managed to break the eyelet on the wiper motor ground wire... Ever had one of those days (or weeks!) where everything you touch turns to ? I call it the meirda touch. Yeah, TWO table saws broke (or were broken), shop vac, an angle grinder, Sawzall, gas grill, door latch, lighting circuit, even a mattock! 😖 I failed to mention that when I replaced my wiper motor, I went with 21" blades. I not only like the added 1.1/2" vertically, but the increased overlap in the center is noticeable. 😀 Link to comment Share on other sites More sharing options...
Gary Lewis Posted August 15, 2019 Author Share Posted August 15, 2019 I failed to mention that when I replaced my wiper motor, I went with 21" blades. I not only like the added 1.1/2" vertically, but the increased overlap in the center is noticeable. 😀 Good tip, Jim. May do that myself as Big Blue goes back together. Link to comment Share on other sites More sharing options...
1986F150Six Posted August 15, 2019 Share Posted August 15, 2019 I failed to mention that when I replaced my wiper motor, I went with 21" blades. I not only like the added 1.1/2" vertically, but the increased overlap in the center is noticeable. 😀 What about the additional load [drag] placed on the wiper components? Link to comment Share on other sites More sharing options...
salans7 Posted August 15, 2019 Share Posted August 15, 2019 I failed to mention that when I replaced my wiper motor, I went with 21" blades. I not only like the added 1.1/2" vertically, but the increased overlap in the center is noticeable. 😀 What about the additional load [drag] placed on the wiper components? WAS going to work on my truck today but mother nature has other plans. Check out that humidity. I guess I'll see what I can do in the shop. Link to comment Share on other sites More sharing options...
Gary Lewis Posted August 15, 2019 Author Share Posted August 15, 2019 WAS going to work on my truck today but mother nature has other plans. Check out that humidity. I guess I'll see what I can do in the shop. Yikes! You could swim in that! Link to comment Share on other sites More sharing options...
salans7 Posted August 15, 2019 Share Posted August 15, 2019 Yikes! You could swim in that! I stepped outside for a few minutes and I was already pouring sweat. It's been raining nonstop so now I'm just inside relaxing. Link to comment Share on other sites More sharing options...
ArdWrknTrk Posted August 16, 2019 Share Posted August 16, 2019 I failed to mention that when I replaced my wiper motor, I went with 21" blades. I not only like the added 1.1/2" vertically, but the increased overlap in the center is noticeable. 😀 What about the additional load [drag] placed on the wiper components? That is my question, David. With the new motor it seems to work fine. Link to comment Share on other sites More sharing options...
Recommended Posts