Quarterwave Posted July 22, 2019 Share Posted July 22, 2019 This looks like the connector that needs to go on a temperature sender that I just purchased for my 351W. I have all the other stuff I need (heat shrink, heat gun etc...) to make a nice, new connection, but cannot find out what this type of connector is called &/or where to buy the basic unit from (without the wire). Link to comment Share on other sites More sharing options...
kramttocs Posted July 23, 2019 Share Posted July 23, 2019 A lot of places call it a "90 Degree Single Contact Female Molded Connector" but you are correct - I am not seeing a place to get just the innards Google jtt2500h or MC-1-ANGLE as those where both the full boot part I found on two different sites Link to comment Share on other sites More sharing options...
kramttocs Posted July 23, 2019 Share Posted July 23, 2019 What about soldering and heat shrinking onto a premade unit? In which case you could get the end from a jy harness for cheap. Link to comment Share on other sites More sharing options...
Steve83 Posted July 23, 2019 Share Posted July 23, 2019 ...what this type of connector is called..."Female bullet" or "barrel'. Link to comment Share on other sites More sharing options...
ArdWrknTrk Posted July 23, 2019 Share Posted July 23, 2019 Gary has the Motorcraft connectors and pigtails catalog up in the documentation. It's sorted by number of contacts, and has pictures of all the pinouts & locking clips. Maybe this is related to the 'catalog' thing, like LMC? ETA, same connector as the starter relay? I think the choke connector is a bigger bullet. Link to comment Share on other sites More sharing options...
Gary Lewis Posted July 23, 2019 Share Posted July 23, 2019 Gary has the Motorcraft connectors and pigtails catalog up in the documentation. It's sorted by number of contacts, and has pictures of all the pinouts & locking clips. Maybe this is related to the 'catalog' thing, like LMC? ETA, same connector as the starter relay? I think the choke connector is a bigger bullet. Using the Ford connector catalog it looks like it is: Googling 3U2Z-14S411-NRA I get to this set of results. And in the pics there's this one from Home Depot - Motorcraft Engine Coolant Temperature Sending Unit Switch Connector. However, this NOS FORD HARDWARE WIRING PIGTAIL KIT PART NUMBER 3U2Z-14S411-NRA NEW from eBay looks to be the same for a lot less money. Link to comment Share on other sites More sharing options...
81f100custom Posted July 23, 2019 Share Posted July 23, 2019 Using the Ford connector catalog it looks like it is: Googling 3U2Z-14S411-NRA I get to this set of results. And in the pics there's this one from Home Depot - Motorcraft Engine Coolant Temperature Sending Unit Switch Connector. However, this NOS FORD HARDWARE WIRING PIGTAIL KIT PART NUMBER 3U2Z-14S411-NRA NEW from eBay looks to be the same for a lot less money. Here it is also at RockAuto. https://www.rockauto.com/en/parts/motorcraft,WPT476,temperature+sender+/+sensor+connector,2564 Link to comment Share on other sites More sharing options...
ArdWrknTrk Posted July 23, 2019 Share Posted July 23, 2019 Here it is also at RockAuto. https://www.rockauto.com/en/parts/motorcraft,WPT476,temperature+sender+/+sensor+connector,2564 Yikes!!! Link to comment Share on other sites More sharing options...
Gary Lewis Posted July 23, 2019 Share Posted July 23, 2019 Yikes!!! Yup. Here's the pics shown in the search link above. Quite a range of prices. I think I like the eBay one. (Don't expect any of those links to work - it is just a picture. ) Link to comment Share on other sites More sharing options...
Steve83 Posted July 23, 2019 Share Posted July 23, 2019 Quite a range of prices.$0.09 each, and you'll have plenty left over to do speakers, or anything else: https://www.amazon.com/dp/B07L5LYHBX If you peel the insulation, it can be bent 90°, and then heat-shrunk (a few layers, if necessary) to make it look like the original one. Link to comment Share on other sites More sharing options...
Recommended Posts