Haystack Posted April 9 Share Posted April 9 Hello all! I have been fighting clutch issues with my 85 cab and chassis f-350. It is the above 8500gvwr with the t-19 and a 460. My clutch fork broke, and apparently it is a over 8500gvwr 85-86 460 or 83-86 6.9 with the t-19 only part. I have been to every junkyard 3 counties in every direction, and haven't found what I need. The regular "under 8500gvwr" f-250 460 uses the t-18 and a different bellhousing, and clutch fork for some reason, and that is all I have been able to source so far. The replacements are not available, (rock auto part number za-126) and appears to have not been available for quite some time. If anyone has an extra one laying around, I would really appreciate it, as well as a picture to verify it is the correct clutch fork. Thank you! Kevin, located near SLC Utah. Link to comment Share on other sites More sharing options...
ArdWrknTrk Posted April 9 Share Posted April 9 No ALL 460's & IDI's use a T-19 I bought a new one for my truck. But it went when I swapped to Zf-5 Kevin, I am a very resourceful individual, and I can help. But I have my rear end torn apart, and have just got out of the hospital, so it may take a bit Again ANY manual IDI or 460 has a T-19💡 I hope this helps, and I will help you. But I have a whole lot of to get done RN. Good luck. Link to comment Share on other sites More sharing options...
1986F150Six Posted April 21 Share Posted April 21 No ALL 460's & IDI's use a T-19 I bought a new one for my truck. But it went when I swapped to Zf-5 Kevin, I am a very resourceful individual, and I can help. But I have my rear end torn apart, and have just got out of the hospital, so it may take a bit Again ANY manual IDI or 460 has a T-19💡 I hope this helps, and I will help you. But I have a whole lot of to get done RN. Good luck. Will this work? [E7TZ-7515-A] https://www.ebay.com/itm/191809151458?fits=Make%3AFord&epid=1117850709&itmmeta=01HW0C54XS30AYP3W95GVS10BJ&hash=item2ca8b761e2:g:EyMAAOSwlJBb4xZH&itmprp=enc%3AAQAJAAAA0CnhWYy5oyXK1Y70DEjeRrfNTcD0ivi3RaRoBroNGV7YYan0w8%2FK2yAQPaZUvaDg6CWB1fXyfvzN%2FUGtWGrMtJKFN5sn8wR4w1915FliiFmnvZ8MufACbhHWGLQN8LGZCym2FZs30wvvkrNVfVZKdCUL0Eao54nFDqGQUtwn0zUep0WaG82fDW7NhR4p6To5dDyllpv9tSyQ5kHRGE2aKqialKNq95s5HornX%2B2nuBrnCAysCmEP9LxcnOLaJTP4Ma2hCldLf%2BKiKXtXjCY2y58%3D%7Ctkp%3ABk9SR_7OlIzgYw Seller states: Flywheel Clutch Release Fork is a direct fit for the following: 1987-1997 Ford F-250 1984-1997 Ford F-350 1987-1997 Ford F Super Duty Designed For Models With Either 7.3L Diesel OR 7.5L Gas Engines Genuine Ford Part Number: E7TZ-7515-A Link to comment Share on other sites More sharing options...
Recommended Posts