RenoHuskerDu Posted December 3, 2021 Share Posted December 3, 2021 Hi mat in tn, Oh yeah its shot, ohm and continuity zero it is toast. I cleaned and re smashed the crimps nothing worked. I am going to turn it in to a single speed fan tomorrow. Thanks for you're post. Mine was shot too, the fusible link in there was an open circuit. I did find a replacement for only about $30 locally, but that was in 2017 before all the dismantling of our economy started. And before I knew that O'Reallys has high prices unless you stick to sale items. Rock Auto has it for less than $20 but of course you need to pay shipping. I always try my local NAPA now first. They actually know about what they sell, shocking. One guy is a carb whiz and sold me his own personal spare needle and seat for Poncho Loco's Holley 2300 yesterday. RockAuto Link to comment Share on other sites More sharing options...
bullnose1985 Posted December 3, 2021 Author Share Posted December 3, 2021 Mine was shot too, the fusible link in there was an open circuit. I did find a replacement for only about $30 locally, but that was in 2017 before all the dismantling of our economy started. And before I knew that O'Reallys has high prices unless you stick to sale items. Rock Auto has it for less than $20 but of course you need to pay shipping. I always try my local NAPA now first. They actually know about what they sell, shocking. One guy is a carb whiz and sold me his own personal spare needle and seat for Poncho Loco's Holley 2300 yesterday. RockAuto Hi Reno, I couldn't find the exact part on rockauto for the first time in awhile. I did find it at a few other retailers. This is the small difference the corner is notched out and the blower box accommodates the corner being cut out. Found one dont recall where but $47.00. I like napa and rockauto too have shopped a bit with a1 auto aswell. Dismantling of the economy for globalism. What a con job. Link to comment Share on other sites More sharing options...
RenoHuskerDu Posted December 3, 2021 Share Posted December 3, 2021 Hi Reno, I couldn't find the exact part on rockauto for the first time in awhile. I did find it at a few other retailers. This is the small difference the corner is notched out and the blower box accommodates the corner being cut out. Found one dont recall where but $47.00. I like napa and rockauto too have shopped a bit with a1 auto aswell. Dismantling of the economy for globalism. What a con job. Click that link I posted, there are 5 types in stock. RockAuto ships pretty fast but it's not cheap. Here's the link again https://www.rockauto.com/en/catalog/ford,1986,f-350,6.9l+420cid+v8+diesel,1126347,heat+&+air+conditioning,blower+motor+control+module+/+resistor,6557 Link to comment Share on other sites More sharing options...
bullnose1985 Posted December 3, 2021 Author Share Posted December 3, 2021 Click that link I posted, there are 5 types in stock. RockAuto ships pretty fast but it's not cheap. Here's the link again https://www.rockauto.com/en/catalog/ford,1986,f-350,6.9l+420cid+v8+diesel,1126347,heat+&+air+conditioning,blower+motor+control+module+/+resistor,6557 Hi Reno, Those look a bit different referring to the corner notch and those appear to be the air conditioner type referring to the ground prong. If i understand correctly the air conditioner had 4 prongs and non air like mine had 3 prongs and a corner of the board cut off. Thanks for your post. Link to comment Share on other sites More sharing options...
bullnose1985 Posted December 13, 2021 Author Share Posted December 13, 2021 Hi mat in tn, Oh yeah its shot, ohm and continuity zero it is toast. I cleaned and re smashed the crimps nothing worked. I am going to turn it in to a single speed fan tomorrow. Thanks for you're post. Hello All, Hope everyone had a good weekend. The single speed rewire is done. I let it run for about 40 minutes today. Ran great and noticeably more air movement. Though thought to be temporary I may make it permanent. My wiring is a mess will tightens it up later. The mockup wiring diagram I used. I wanted to keep everyone posted. All done and works better then expected....... So far. Thanks for your interest and input.. Link to comment Share on other sites More sharing options...
Gary Lewis Posted December 14, 2021 Share Posted December 14, 2021 Hello All, Hope everyone had a good weekend. The single speed rewire is done. I let it run for about 40 minutes today. Ran great and noticeably more air movement. Though thought to be temporary I may make it permanent. My wiring is a mess will tightens it up later. The mockup wiring diagram I used. I wanted to keep everyone posted. All done and works better then expected....... So far. Thanks for your interest and input.. Glad it worked so well. Thanks for following up. Link to comment Share on other sites More sharing options...
bullnose1985 Posted December 15, 2021 Author Share Posted December 15, 2021 Glad it worked so well. Thanks for following up. Thank you for your input, time and effort. Link to comment Share on other sites More sharing options...
Recommended Posts