Jason2215 Posted September 17, 2020 Posted September 17, 2020 Hey all. I ran this by folks on another forum and got some great troubleshooting advice but I'm still getting stuck so I bring it to you, the bullnose experts for guidance! First a recap of what is happening and what I've done. One caveat, I'm EXTREMELY novice with electrical wiring. Trying to chase these wires gives me anxiety!: 1984 Bronco, 351W, C6. When purchased back in Feb/March I test drove the truck, started fine (twice, once to test drive, the other to load it on the trailer) and then brought it home. Over the course of a few days, it would intermittently not start. No discernable sounds other than the faint click of the starter. I wasn't too worried because I'd be parking it to do some upgrades (not related). Fast forward to today, I'm ready to figure out the starting issue. The previous owner had installed what I now know to be a PMGR starter (the one with the solenoid attached?) and had wired the ignition without utilizing the fender mounted solenoid (the black one with 4 posts?) so it just sits there empty. As best I can tell, the wiring runs straight from the battery (large positive cable only) directly to the starter and there are two brown-ish wires with some sort of embedded fuse on them hooked to the same post on the starter (not sure where those originate from) and then what I think is the ignition wire (smaller red wire) on the other post of the starter. The truck will fire every now and then. And I mean every now and then. Maybe once or twice every 50 times I turn the key, randomly. When it does, it fires up great. Then nothing. Just a click of the starter. I'd like to get the wiring back to "original" as required as I'm fairly certain this is my issue. Awhile back I started shotgunning fixes at it (I know, I know) and here is what has been replaced: - Key lock cylinder (key was sticking in "start" - Ignition Switch - Ignition Module - Starter - Battery Tested good/tried 2nd battery as well - Cleaned grounding areas to ensure good connections I have read the PMGR how to page on this forum and I'm ready to give that a try, but I am not 100% sure where to run those additional (smaller) wires FROM and where to tie them into on the fender mounted solenoid (if at all). The larger battery cable seems simple enough. Also, would the way the previous owner has it wired now negatively effect the truck how I've described? Is there some electrical load being effected by having everything wired directly to the starter? The only other thing I can think of that I haven't tried is the neutral safety switch. Keep in mind I AM getting a one-click response from the starter when I turn the key and every once in awhile (hardly ever) it starts right up.
85lebaront2 Posted September 17, 2020 Posted September 17, 2020 The problem is twofold, first, the ignition switch on the older Fords is not capable of handling the current draw of the PMGR starter. The second part is because of that the switch is probably bad. The first application I had with a factory PMGR starter was a 1990 Lincoln Town Car we owned. It had the PMGR starter, and used a Bosch relay underhood to engage it. The way I and others have done for the PMGR is to retain the standard Ford relay and wire it with the original hot side (including the fusible links) on the front large post and the large cable to the starter also there. The existing red/blue wire from the starter terminal on the ignition switch goes to the "S" stud. The other large terminal is where the "trigger" wire to the solenoid goes. If you don't want to mess with the big Ford relay, a weather proof Bosch relay can be used, but needs a weatherproof socket. A good source for both is Chrysler built minivans from the early to mid 90s, they have a row of them on the driver's side fender.
Jason2215 Posted September 17, 2020 Author Posted September 17, 2020 The problem is twofold, first, the ignition switch on the older Fords is not capable of handling the current draw of the PMGR starter. The second part is because of that the switch is probably bad. The first application I had with a factory PMGR starter was a 1990 Lincoln Town Car we owned. It had the PMGR starter, and used a Bosch relay underhood to engage it. The way I and others have done for the PMGR is to retain the standard Ford relay and wire it with the original hot side (including the fusible links) on the front large post and the large cable to the starter also there. The existing red/blue wire from the starter terminal on the ignition switch goes to the "S" stud. The other large terminal is where the "trigger" wire to the solenoid goes. If you don't want to mess with the big Ford relay, a weather proof Bosch relay can be used, but needs a weatherproof socket. A good source for both is Chrysler built minivans from the early to mid 90s, they have a row of them on the driver's side fender. Thanks for the quick reply! So, just to be sure I understand your wiring recommendation, (again, comfort level near zero ) is what you are describing like the picture below? Also, so I completely understand and don't blow myself up, I take the existing smaller red wire that is connected to the starter, and connect that to the fender mounted relay on the "S" terminal (from wherever it originates from currently). I take the two fusable (brown?) wires that are currently on the starter post with the + battery cable and connect those to the battery side post of the fender mounted relay (along with the + battery cable) from wherever they originate from currently. Then i can take an additional smaller gauge wire(?) and connect it from the output side of the relay (as in pic below) and connect the other end to the smaller ignition terminal on the starter, where my existing small red wire is currently connected. Is this correct? I could be totally off. Also, this will help fix the issues with the PMGR starter/ignition switch? I'm assuming my ignition switch is good since I'm having the same issues with the new switch installed as I did with the previous one, at least unless I'm missing something else. Thanks in advance for your patience!
Gary Lewis Posted September 17, 2020 Posted September 17, 2020 Thanks for the quick reply! So, just to be sure I understand your wiring recommendation, (again, comfort level near zero ) is what you are describing like the picture below? Also, so I completely understand and don't blow myself up, I take the existing smaller red wire that is connected to the starter, and connect that to the fender mounted relay on the "S" terminal (from wherever it originates from currently). I take the two fusable (brown?) wires that are currently on the starter post with the + battery cable and connect those to the battery side post of the fender mounted relay (along with the + battery cable) from wherever they originate from currently. Then i can take an additional smaller gauge wire(?) and connect it from the output side of the relay (as in pic below) and connect the other end to the smaller ignition terminal on the starter, where my existing small red wire is currently connected. Is this correct? I could be totally off. Also, this will help fix the issues with the PMGR starter/ignition switch? I'm assuming my ignition switch is good since I'm having the same issues with the new switch installed as I did with the previous one, at least unless I'm missing something else. Thanks in advance for your patience! Bill may be along in a bit, but I'm not sure your words match what the drawings show. So let me say it in my words. You'll have a large wire, the positive battery cable, from the battery to the front large terminal of the starter relay. And from the same terminal you'll have a large wire down to the starter. In addition, if the "two fusable (brown?) wires" are truly fuse links they will go on that same terminal. What that does is provide power 100% of the time to the starter and the fuse links. Then from the rear side of the starter relay, the other large terminal, you will have a smaller wire going to the small terminal on the starter. The red/blue wire that comes from the ignition switch should already be hooked to the small front terminal of the starter relay. Does that make sense?
Jason2215 Posted September 17, 2020 Author Posted September 17, 2020 Bill may be along in a bit, but I'm not sure your words match what the drawings show. So let me say it in my words. You'll have a large wire, the positive battery cable, from the battery to the front large terminal of the starter relay. And from the same terminal you'll have a large wire down to the starter. In addition, if the "two fusable (brown?) wires" are truly fuse links they will go on that same terminal. What that does is provide power 100% of the time to the starter and the fuse links. Then from the rear side of the starter relay, the other large terminal, you will have a smaller wire going to the small terminal on the starter. The red/blue wire that comes from the ignition switch should already be hooked to the small front terminal of the starter relay. Does that make sense? Thanks Gary (and Bill)!! I think so. POS Battery cables (2) from batt to relay then relay to starter (same relay post). Then (this is where I’m getting really confused) I’ll need to figure out where the two fused links are originating from and move them to the same relay post as the batt cables, then route them to the same post on the starter as the pos batt cable (I’m not sure I’m correct there. Or are you saying they go to the same terminal on the starter itself as they are in my original picture?) OR, keep them from where they currently originate and end them on the same fender relay post as the large batt and starter cables Next, the other smaller wire from relay to starter I understand. I’ll have to make that one as it doesn’t exist on mine now. Last, the red/blue wire from the ignition switch. The wire that is currently connected to my starter is only red (it’s the one on its own in my original picture) but could be spliced in somewhere with the red/blue so I’m assuming that’s the wire in question. However, you said it should already be hooked to the small front terminal on the starter relay, but mine is not. I have nothing connected to that fender mounted relay. Should I move that wire from the starter to the terminal on the fender relay labeled “S”? When I’m done, the four wires I have connected directly to the starter will be reduced to one large and one small cable (both from the relay) and the ignition wire and two fused links will end at my fender relay. ....I think.... I know this is probably painful but I’d really like to be able to fix this one without giving up. Even with the EVTM manual I’m lost.
85lebaront2 Posted September 18, 2020 Posted September 18, 2020 Thanks Gary (and Bill)!! I think so. POS Battery cables (2) from batt to relay then relay to starter (same relay post). Then (this is where I’m getting really confused) I’ll need to figure out where the two fused links are originating from and move them to the same relay post as the batt cables, then route them to the same post on the starter as the pos batt cable (I’m not sure I’m correct there. Or are you saying they go to the same terminal on the starter itself as they are in my original picture?) OR, keep them from where they currently originate and end them on the same fender relay post as the large batt and starter cables Next, the other smaller wire from relay to starter I understand. I’ll have to make that one as it doesn’t exist on mine now. Last, the red/blue wire from the ignition switch. The wire that is currently connected to my starter is only red (it’s the one on its own in my original picture) but could be spliced in somewhere with the red/blue so I’m assuming that’s the wire in question. However, you said it should already be hooked to the small front terminal on the starter relay, but mine is not. I have nothing connected to that fender mounted relay. Should I move that wire from the starter to the terminal on the fender relay labeled “S”? When I’m done, the four wires I have connected directly to the starter will be reduced to one large and one small cable (both from the relay) and the ignition wire and two fused links will end at my fender relay. ....I think.... I know this is probably painful but I’d really like to be able to fix this one without giving up. Even with the EVTM manual I’m lost. Your drawing is exactly correct sir. The fusible links are what go to the alternator and inside the cab, they are spliced onto the ends of what should probably be yellow 8 or 10 ga wires. Good luck with it!
Jason2215 Posted September 18, 2020 Author Posted September 18, 2020 Your drawing is exactly correct sir. The fusible links are what go to the alternator and inside the cab, they are spliced onto the ends of what should probably be yellow 8 or 10 ga wires. Good luck with it! Thanks Bill! I was wondering where those wires connected to. It’s hard to follow them w the mess of wires in there. So unless someone says otherwise it’s fused ends on the fender relay along with red ignition wire and two battery cables. Then one battery cable to the starter and one smaller 8/10ga wire from fender relay to smaller starter terminal. So, how does this configuration help the ignition switch power the PMGR starter better than wiring everything straight to the starter? Hoping this fixes my issues!
Jason2215 Posted September 18, 2020 Author Posted September 18, 2020 Your drawing is exactly correct sir. The fusible links are what go to the alternator and inside the cab, they are spliced onto the ends of what should probably be yellow 8 or 10 ga wires. Good luck with it! Re-reading your initial post and now I can start to see exactly what you’re saying for the routing (finally) and it appears to mirror what I’ve stated above, so this will be my project tomorrow! I’ll report back hoping it helps crank this starter. Thanks again!
Frank Wyatt Posted September 18, 2020 Posted September 18, 2020 Thanks Bill! I was wondering where those wires connected to. It’s hard to follow them w the mess of wires in there. So unless someone says otherwise it’s fused ends on the fender relay along with red ignition wire and two battery cables. Then one battery cable to the starter and one smaller 8/10ga wire from fender relay to smaller starter terminal. So, how does this configuration help the ignition switch power the PMGR starter better than wiring everything straight to the starter? Hoping this fixes my issues! It takes the load off the ignition witch so the switch does not have to carry the full starting amperage. Like this, it's only pulling enough amperage to energize the starting relay.
Jason2215 Posted September 18, 2020 Author Posted September 18, 2020 It takes the load off the ignition witch so the switch does not have to carry the full starting amperage. Like this, it's only pulling enough amperage to energize the starting relay. Thanks Frank! I wish I was smarter on this stuff. But that does make sense
Recommended Posts