screaminL Posted April 11 Share Posted April 11 1/3 of the time it stalls after starting than starts and runs fine. New plugs, cap, rotor, fuel filter I serviced transmission and Filter drained tqe converter new fmco oil 12 qts seems to hit all shift points when slowing down to almost a stop or stop transmission slips wont take off again I put in park run thru gears and it drives away fine I set TV cable in park motor off all loose and snaped on. Link to comment Share on other sites More sharing options...
mat in tn Posted April 11 Share Posted April 11 very strange description. but mostly it sounds as if the tv cable is too tight. but let's not assume. you say that you can feel all downshifts. they should be nearly unnoticeable. how well do you feel the upshifts? do they seem to be a little late but firm? is there any chance that you have a pressure gauge to read the tv initial response pressure? Link to comment Share on other sites More sharing options...
screaminL Posted April 12 Author Share Posted April 12 very strange description. but mostly it sounds as if the tv cable is too tight. but let's not assume. you say that you can feel all downshifts. they should be nearly unnoticeable. how well do you feel the upshifts? do they seem to be a little late but firm? is there any chance that you have a pressure gauge to read the tv initial response pressure? the shifts are smooth up and down it truly acts normal untill the down shift to low that becomes nothing what are the threads on the transmission to hook gage to? what should be the pressure? Link to comment Share on other sites More sharing options...
mat in tn Posted April 12 Share Posted April 12 the shifts are smooth up and down it truly acts normal untill the down shift to low that becomes nothing what are the threads on the transmission to hook gage to? what should be the pressure? there are a few taps, one on the driver side for testing the pressure coming from the pump. 1/8" npt. if you have a gauge set it will have these adapters. there are three on the passenger side, but they can be a little harder to reach due to the catalytic converter is right there. harder if it's hot! the rearmost tap is for the direct clutch literally one inch from the tail shaft housing. the next one going forward is for throttle valve set pressure. it is back in a bit of a recess and harder to see. I use a 2" nipple with a brass 90 on the end (these two are tightened on a vise beforehand to make them one and then much easier to install and remove). the most important pressure to measure is tv. at idle it needs to be below 5 psi but is best at 0 with immediate throttle response. too late and clutches slip when they need to grip and too much pressure and they don't relax when they should. if you are only testing tv pressure then a 0-100 gauge is ok but if you are testing pump output you need one capable of reading 0-300 psi. average under throttle can be 180-220 and this is very variable as it depends on many factors but mainly rpm. an automatic is a pump first and a transmission second. Link to comment Share on other sites More sharing options...
Gary Lewis Posted April 12 Share Posted April 12 there are a few taps, one on the driver side for testing the pressure coming from the pump. 1/8" npt. if you have a gauge set it will have these adapters. there are three on the passenger side, but they can be a little harder to reach due to the catalytic converter is right there. harder if it's hot! the rearmost tap is for the direct clutch literally one inch from the tail shaft housing. the next one going forward is for throttle valve set pressure. it is back in a bit of a recess and harder to see. I use a 2" nipple with a brass 90 on the end (these two are tightened on a vise beforehand to make them one and then much easier to install and remove). the most important pressure to measure is tv. at idle it needs to be below 5 psi but is best at 0 with immediate throttle response. too late and clutches slip when they need to grip and too much pressure and they don't relax when they should. if you are only testing tv pressure then a 0-100 gauge is ok but if you are testing pump output you need one capable of reading 0-300 psi. average under throttle can be 180-220 and this is very variable as it depends on many factors but mainly rpm. an automatic is a pump first and a transmission second. Don't forget that we have the factory shop manual instructions on the AOD/AOT here. Link to comment Share on other sites More sharing options...
85lebaront2 Posted April 12 Share Posted April 12 there are a few taps, one on the driver side for testing the pressure coming from the pump. 1/8" npt. if you have a gauge set it will have these adapters. there are three on the passenger side, but they can be a little harder to reach due to the catalytic converter is right there. harder if it's hot! the rearmost tap is for the direct clutch literally one inch from the tail shaft housing. the next one going forward is for throttle valve set pressure. it is back in a bit of a recess and harder to see. I use a 2" nipple with a brass 90 on the end (these two are tightened on a vise beforehand to make them one and then much easier to install and remove). the most important pressure to measure is tv. at idle it needs to be below 5 psi but is best at 0 with immediate throttle response. too late and clutches slip when they need to grip and too much pressure and they don't relax when they should. if you are only testing tv pressure then a 0-100 gauge is ok but if you are testing pump output you need one capable of reading 0-300 psi. average under throttle can be 180-220 and this is very variable as it depends on many factors but mainly rpm. an automatic is a pump first and a transmission second. Mat, it sounds like he has a valve body issue, due to the no drive in 1st after slowing way down or stopping. In OD the forward clutch is released to allow the OD band to hold the front drum. If the valve controlling the forward clutch is sticking (and it could be more than one) the transmission will effectively be in neutral when it downshifts. I was trying to find a hydraulic diagram for it, but I am drawing a blank. There is a TSB (85-10-12) regarding the 3-4 shift valve design change that addresses a no drive condition after a coast down from 4th gear. 1985 Ford Truck F 150 2WD Pickup V8-302 5.0L VIN N FI Copyright © 2013, ALLDATA 10.52SS Page 1 Valve Body: All Technical Service Bulletins A/T - AOD No Forward Drive Condition Article No. 85-10-12 TRANSMISSION - AUTOMATIC - AOD - NO FORWARD DRIVE AFTER COAST DOWN FROM FOURTH GEAR FORD 1983-1985 FORD, THUNDERBIRD, LTD, MUSTANG LINCOLN-MERCURY 1983-85 MERCURY, COUGAR, MARQUIS, CAPRI, LINCOLN, MARK, CONTINENTAL LIGHT TRUCK 1983-85 E & F SERIES Some AOD-equipped vehicles with transmissions built between March, 1983 and April 19, 1985, may exhibit a no forward drive condition after coast down from fourth gear. This condition may occur if a small particle of contamination causes the 3-4 shift valve to stick in the forward clutch exhaust position. Figure 11 - 3-4 SHIFT VALVE DESIGN To service this condition, install a new 3-4 shift valve that has a design with flats on the valve. This will allow contamination to pass and be trapped in the main control filter assembly. The new valve was incorporated in production April 19, 1985. Refer to Figure 11 for visual differences between 3-4 shift valve design levels. PROCEDURE: 1. Verify that the transmission was built between March 1, 1983 and April 9, 1985. 2. Remove the main control assembly from the vehicle according to the Main Control Removal Procedure in Section 17-20 of the appropriate model year Car or Truck Shop Manual. 3. Partially disassemble the valve body to expose the valve body face by following Steps 1 and 2 of the Valve Body Disassembly Procedure in Section 17- 20 of the Shop Manual. This involves removing the separator plate, valve body gasket and all check balls. 4. Attempt to verify the concern by visually checking the 3-4 shift valve to see if a small particle of contamination is blocking the valve. 5. Remove the 3-4 shift valve bore sleeve from bore No. 5 as illustrated in the Shop Manual. The valve should fall out freely. Remove all springs and the 3-4 TV modulator valve. 6. Thoroughly clean the bore passage with solvent. 7. Pour solvent cleaner over the valve body face, spill solvent from passages, and blow dry with clean compressed air. 8. Replace the 3-4 shift valve with the flatted design (Part No. E5AZ-7F259-A). Reassemble the 3-4 TV modulator valve and spring, the new 3-4 shift valve and spring, the throttle plug sleeve, and the retaining clip in bore No. 5 as illustrated in the Shop Manual. 9. Reassemble the valve body by reversing Steps 1 and 2 of the Valve Body Disassembly Procedure. Be sure to use a new valve body gasket. 10. Reinstall the valve body by reversing Steps 1 and 2 of the Valve Body Disassembly Procedure. Be sure to use a new valve body gasket. 11. Reinstall the valve body on the transmission according to the Valve Body Installation Procedure in Section 17-20 of the Shop Manual. PART NUMBER PART NAME CLASS E5AZ-7F259-A 3-4 Shift Valve C OTHER APPLICABLE ARTICLES: None 1985 Ford Truck F 150 2WD Pickup V8-302 5.0L VIN N FI Copyright © 2013, ALLDATA 10.52SS Page 2 WARRANTY STATUS: Reimbursable within the provisions of the Warranty and Policy Manual. OPERATION: Refer to the Labor Standards Manual for applicable operation and time. 77396A2 TIME: 1.3 Hrs. DLR CODING: Basic Part No. 7A100 - Code: 41 Link to comment Share on other sites More sharing options...
screaminL Posted April 13 Author Share Posted April 13 Mat, it sounds like he has a valve body issue, due to the no drive in 1st after slowing way down or stopping. In OD the forward clutch is released to allow the OD band to hold the front drum. If the valve controlling the forward clutch is sticking (and it could be more than one) the transmission will effectively be in neutral when it downshifts. I was trying to find a hydraulic diagram for it, but I am drawing a blank. There is a TSB (85-10-12) regarding the 3-4 shift valve design change that addresses a no drive condition after a coast down from 4th gear. 1985 Ford Truck F 150 2WD Pickup V8-302 5.0L VIN N FI Copyright © 2013, ALLDATA 10.52SS Page 1 Valve Body: All Technical Service Bulletins A/T - AOD No Forward Drive Condition Article No. 85-10-12 TRANSMISSION - AUTOMATIC - AOD - NO FORWARD DRIVE AFTER COAST DOWN FROM FOURTH GEAR FORD 1983-1985 FORD, THUNDERBIRD, LTD, MUSTANG LINCOLN-MERCURY 1983-85 MERCURY, COUGAR, MARQUIS, CAPRI, LINCOLN, MARK, CONTINENTAL LIGHT TRUCK 1983-85 E & F SERIES Some AOD-equipped vehicles with transmissions built between March, 1983 and April 19, 1985, may exhibit a no forward drive condition after coast down from fourth gear. This condition may occur if a small particle of contamination causes the 3-4 shift valve to stick in the forward clutch exhaust position. Figure 11 - 3-4 SHIFT VALVE DESIGN To service this condition, install a new 3-4 shift valve that has a design with flats on the valve. This will allow contamination to pass and be trapped in the main control filter assembly. The new valve was incorporated in production April 19, 1985. Refer to Figure 11 for visual differences between 3-4 shift valve design levels. PROCEDURE: 1. Verify that the transmission was built between March 1, 1983 and April 9, 1985. 2. Remove the main control assembly from the vehicle according to the Main Control Removal Procedure in Section 17-20 of the appropriate model year Car or Truck Shop Manual. 3. Partially disassemble the valve body to expose the valve body face by following Steps 1 and 2 of the Valve Body Disassembly Procedure in Section 17- 20 of the Shop Manual. This involves removing the separator plate, valve body gasket and all check balls. 4. Attempt to verify the concern by visually checking the 3-4 shift valve to see if a small particle of contamination is blocking the valve. 5. Remove the 3-4 shift valve bore sleeve from bore No. 5 as illustrated in the Shop Manual. The valve should fall out freely. Remove all springs and the 3-4 TV modulator valve. 6. Thoroughly clean the bore passage with solvent. 7. Pour solvent cleaner over the valve body face, spill solvent from passages, and blow dry with clean compressed air. 8. Replace the 3-4 shift valve with the flatted design (Part No. E5AZ-7F259-A). Reassemble the 3-4 TV modulator valve and spring, the new 3-4 shift valve and spring, the throttle plug sleeve, and the retaining clip in bore No. 5 as illustrated in the Shop Manual. 9. Reassemble the valve body by reversing Steps 1 and 2 of the Valve Body Disassembly Procedure. Be sure to use a new valve body gasket. 10. Reinstall the valve body by reversing Steps 1 and 2 of the Valve Body Disassembly Procedure. Be sure to use a new valve body gasket. 11. Reinstall the valve body on the transmission according to the Valve Body Installation Procedure in Section 17-20 of the Shop Manual. PART NUMBER PART NAME CLASS E5AZ-7F259-A 3-4 Shift Valve C OTHER APPLICABLE ARTICLES: None 1985 Ford Truck F 150 2WD Pickup V8-302 5.0L VIN N FI Copyright © 2013, ALLDATA 10.52SS Page 2 WARRANTY STATUS: Reimbursable within the provisions of the Warranty and Policy Manual. OPERATION: Refer to the Labor Standards Manual for applicable operation and time. 77396A2 TIME: 1.3 Hrs. DLR CODING: Basic Part No. 7A100 - Code: 41 cold in park I have over 50psi at the TV port? Link to comment Share on other sites More sharing options...
mat in tn Posted April 13 Share Posted April 13 cold in park I have over 50psi at the TV port? whoa! it should be closer to zero! like zero! try this. disconnect the cable at the transmission end and test it again. I would expect 20-30. then reconnect and disconnect the throttle body end and retest. it should be zero. these tests will lead us in one of two directions. Link to comment Share on other sites More sharing options...
screaminL Posted April 14 Author Share Posted April 14 whoa! it should be closer to zero! like zero! try this. disconnect the cable at the transmission end and test it again. I would expect 20-30. then reconnect and disconnect the throttle body end and retest. it should be zero. these tests will lead us in one of two directions. when attached to transmission and disconnected at throttle it is above 50 when disconnected at trans it is zero- I do not see an adjustment at the transmission the cable is about 3/8" long is the lever the tv cable hooks to kinda free floating slighty ahead of all the way back or should it be in a position held internaly? and thank you for the help Link to comment Share on other sites More sharing options...
mat in tn Posted April 14 Share Posted April 14 when attached to transmission and disconnected at throttle it is above 50 when disconnected at trans it is zero- I do not see an adjustment at the transmission the cable is about 3/8" long is the lever the tv cable hooks to kinda free floating slighty ahead of all the way back or should it be in a position held internaly? and thank you for the help with the tv cable disconnected at the trans. the tv lever should be able to be moved forward very easily to a stop. then easily back to a stop. yet as you let go of it, it should spring back from the rear stop a little. there should be a little spring back resistance when pushing it rearward repeatably. however, with the cable disconnected at the throttle body it shows 50 but disconnected at the trans shows zero. that sounds like the problem is in the tv cable assembly itself. has it been off? was it put back on correctly has the tv arm been off? has it been put back on correctly? the factory tv cable has a lower portion with a corrugated rubber cover covering a return spring. this is to push the tv lever rearward to the stop to achieve zero psi. the upper end holds the adjuster. its most likely a mis adjustment but even the cable assembly is a mechanical part which can fail. not too common though. anyways look for signs of something having been worked on or go back to something you did. last thing touched etc. Link to comment Share on other sites More sharing options...
Recommended Posts