Praetorian Posted September 27, 2023 Share Posted September 27, 2023 So I just bought an 85 Bullnose Bronco that I believe was converted to a 351W EFI manual with both high and low pressure pumps. Titile says it was originally a V6. EEC and FP relays are getting power but there is no power going to the intank pump. In tank pump is new. My question is: when this rig was converted with the 351 EFI, would there need to be a corresponding inertia switch? Or can it function without it? I’m thinking there has to be one but I can’t find the damn thing. Checked in all the locations under the dash and kickpanels but don’t see anything resembling one. I’m also mediocre at best when testing electrical. Any help would be appreciated and thank you in advance! Link to comment Share on other sites More sharing options...
85lebaront2 Posted September 27, 2023 Share Posted September 27, 2023 If it had one it would probably be where the factory EFI or hot fuel handling package had them, on the heater air duct, just to the right side on center. Link to comment Share on other sites More sharing options...
Praetorian Posted September 27, 2023 Author Share Posted September 27, 2023 If it had one it would probably be where the factory EFI or hot fuel handling package had them, on the heater air duct, just to the right side on center. Thanks for the response. I’m going to look deeper when I get home today. There has to be one or maybe it’s missing. Tons of cut wires and disconnected connectors, loose connectors, etc. This truck is pretty beat up and a wiring nightmare. Link to comment Share on other sites More sharing options...
85lebaront2 Posted September 27, 2023 Share Posted September 27, 2023 Thanks for the response. I’m going to look deeper when I get home today. There has to be one or maybe it’s missing. Tons of cut wires and disconnected connectors, loose connectors, etc. This truck is pretty beat up and a wiring nightmare. Ok, the wires on Darth were yellow and came through the firewall under the AC case. Link to comment Share on other sites More sharing options...
James191145 Posted September 28, 2023 Share Posted September 28, 2023 If it had one it would probably be where the factory EFI or hot fuel handling package had them, on the heater air duct, just to the right side on center. Just something to check out while your in there...... There is a small ground wire (maybe 12gauge) near the battery that HAS to be connected to ground. This probably isnt your problem but it is crucial and no pump will run without it. Link to comment Share on other sites More sharing options...
Praetorian Posted September 28, 2023 Author Share Posted September 28, 2023 Just something to check out while your in there...... There is a small ground wire (maybe 12gauge) near the battery that HAS to be connected to ground. This probably isnt your problem but it is crucial and no pump will run without it. Yes, you are right. That was the last thing I checked last night. I traced the fuel pump wires to a 5 pin relay mounted near the radiator. Power feeds the relay from the solenoid. The relay is getting power but looks like power is not coming out to the fuel pump wires. I did replace the relay. This relay btw is separate from the FP relay and is mounted on the radiator close to the battery I did see a ground wire from the relay that had snapped off the firewall. I was hoping this was the problem but unfortunately no. I think my next step is to replace the fusable link wire from this relay which may have shorted out. I’ve heard of these wires but never actually seen one inaction. Or plan b is to just bypass that relay altogether and hook the pump wires to the solenoid? Link to comment Share on other sites More sharing options...
Praetorian Posted September 30, 2023 Author Share Posted September 30, 2023 Yes, you are right. That was the last thing I checked last night. I traced the fuel pump wires to a 5 pin relay mounted near the radiator. Power feeds the relay from the solenoid. The relay is getting power but looks like power is not coming out to the fuel pump wires. I did replace the relay. This relay btw is separate from the FP relay and is mounted on the radiator close to the battery I did see a ground wire from the relay that had snapped off the firewall. I was hoping this was the problem but unfortunately no. I think my next step is to replace the fusable link wire from this relay which may have shorted out. I’ve heard of these wires but never actually seen one inaction. Or plan b is to just bypass that relay altogether and hook the pump wires to the solenoid? So I bypassed that extra relay and spliced the hot wires together and now the pumps work. Getting fuel to the engine it fires and keeps running when I pump the gas. The minute I let off the gas it immediately dies. Adjusted the idle nut and now it stays running. Will do more checks tomorrow. Thanks for the help! Link to comment Share on other sites More sharing options...
Recommended Posts